VOR1142M4 www.vishay.com vishay semiconductors rev. 1.1, 17-nov-15 1 document number: 84301 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 1 form a solid-state relay description the vor1142 is an spst normally open switch (1 form a) that can replace electromechanical relays in many applications. it is constructed using a gaalas ired actuation control and mosfets for the switch output. features ? current limit protection ? isolation test voltage 3750 v rms ? typical r on 22 ? load voltage 400 v ? load current 140 ma ? high surge capability ? clean bounce free switching ? low power consumption ? high temperature range ? material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912 applications ? general telecom switching ? metering ? security equipment ? instrumentation ? industrial controls ? battery management systems ? automatic measurement equipment agency approvals ? ul1577, file no. e52744 ? din en 60747-5-5 (vde0884-5) a c s 1 s 2 1 2 4 3 ordering information vor1 1 4 2m4 # part number package configuration package ul, vde sop-4, tape and reel VOR1142M4t sop-4, tube VOR1142M4 s op-4 7.21 mm
VOR1142M4 www.vishay.com vishay semiconductors rev. 1.1, 17-nov-15 2 document number: 84301 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? stresses in excess of the absolu te maximum ratings can ca use permanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of th e time can adversely affect reliability. (1) for continuous negative potential from output side to input side only 85 c is allowed. note ? minimum and maximum values are testing requirements. typical values are characteristics of the device and are the result of en gineering evaluations. typical values are for information only and are not part of the testing requirements. absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter conditions symbol value unit input ired continuous forward current i f 50 ma ired reverse voltage v r 5v input power dissipation p diss 80 mw output dc or peak ac load voltage v l 400 v continuous dc load current i l 140 ma ssr output power dissipation p diss 550 mw ssr ambient temperature range (1) t amb -40 to +100 c storage temperature range t stg -40 to +150 c soldering temperature t = 10 s max. t sld 260 c electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit input ired forward current, switch turn-on i l = 100 ma, t = 10 ms i fon -0.252 ma ired forward current, switch turn-off v l = 350 v, i l < 1 a i foff 0.05 0.15 - ma ired forward voltage i f = 10 ma v f - 1.36 1.5 v ired reverse current v r = 5 v i r - - 10 a output on-resistance i f = 5 ma, i l = 50 ma r on -2227 off-resistance i f = 0 ma, v l = 100 v r off 0.5 850 - g off-state leakage current i f = 0 ma, v l = 100 v i leak - < 1 100 na i f = 0 ma, v l = 400 v i leak - 6 500 na output capacitance i f = 0 ma, v l = 1 v, 1 mhz c o -39-pf i f = 0 ma, v l = 50 v, 1 mhz c o -6-pf current limit ac/dc i f = 5 ma, t = 5 ms, v l = 6 v i limit 170 300 450 ma coupler capacitance (input to output) v io = 1 v c io -0.4- pf
VOR1142M4 www.vishay.com vishay semiconductors rev. 1.1, 17-nov-15 3 document number: 84301 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 1 - timing schematic note ? as per iec 60747-5-5, 7.4.3.8.2, this optoco upler is suitable for safe electrical in sulation only within the safety ratings . compliance with the safety ratings shall be ensured by means of protective circuits. switching characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit turn-on time i f = 5 ma, i l = 50 ma t on -0.20.5ms turn-off time i f = 5 ma, i l = 50 ma t off - 0.05 0.2 ms safety and insulation ratings parameter test condition symbol value unit climatic classifica tion according to iec 68 part 1 40/100/21 pollution degree according to din vde 0109 2 comparative tracking index cti 175 maximum rated withstanding isolation vo ltage according to ul1577, t = 1 min v iso 3750 v rms maximum transient isol ation voltage according to din en 60747-5-5 v iotm 6000 v peak maximum repetitive peak isolation voltage acc ording to din en 60747-5-5 v iorm 707 v peak isolation resistance t amb = 25 c, v io = 500 v r io 10 12 t amb = 100 c, v io = 500 v r io 10 11 output safety power p so 550 mw input safety current i si 180 ma input safety temperature t s 175 c clearance distance sop-4 5mm creepage distance sop-4 5mm insulation thickness dti 0.3 mm input to output test voltage, method b v iorm x 1.875 = v pr , 100 % production test with t m = 1 s, partial discharge < 5 pc v pr 1326 v peak input to output test voltage, method a v iorm x 1.6 = v pr , sample test with t m = 10 s, partial disc harge < 5 pc v pr 1131 v peak input output 90 % 10 % t on t off a c v l output 1 2 4 3
VOR1142M4 www.vishay.com vishay semiconductors rev. 1.1, 17-nov-15 4 document number: 84301 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 2 - safety input current vs. am bient temperature fig. 3 - safety powe r dissipation vs. ambient temperature typical characteristics (t amb = 25 c, unless otherwise specified) fig. 4 - maximum load current vs. ambient temperature fig. 5 - forward voltage vs. ambient temperature fig. 6 - forward current vs. forward voltage fig. 7 - normalized forward current for switch turn-on vs. ambient temperature 0 50 100 150 200 250 -50-250 255075100125150175 i s i - input s afety current (ma) t amb - ambient temperature ( c) 0 200 400 600 800 -50-250 255075100125150175 p s o -output s afety power (mw) t amb - ambient temperature ( c) 0 20 40 60 80 100 120 140 160 -40-200 20406080100120 i l - load current (ma) t amb - ambient temperature ( c) i f > 5 ma 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 -40-200 20406080100 v f - forward voltage (v) t amb - ambient temperature ( c) i f = 10 ma i f = 5 ma i f = 2 ma 0 10 20 30 40 50 60 0 0.5 1.0 1.5 2.0 i f - forward current (ma) v f - forward voltage (v) t amb = 100 c t amb = 25 c t amb = -40 c 0 0.5 1.0 1.5 2.0 2.5 -40 -20 0 20 40 60 80 100 normalized forward current for s witch turn-on t amb - ambient temperature ( c) normalized to t amb = 25 c i l = 100 ma
VOR1142M4 www.vishay.com vishay semiconductors rev. 1.1, 17-nov-15 5 document number: 84301 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 8 - normalized on-resistance vs. ambient temperature fig. 9 - output capacitance vs. load voltage fig. 10 - off-state leakage current vs. load voltage fig. 11 - turn-on time vs. forward current fig. 12 - normalized turn-on time vs. ambient temperature fig. 13 - turn-off time vs. forward current 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 -40 -20 0 20 40 60 80 100 normalized on-re s i s tance t amb - ambient temperature ( c) normalized to t amb = 25 c i f = 5.0 ma i l = 50 ma 0 10 20 30 40 50 60 0 102030405060 v l - load voltage (v) i f = 0 ma f = 1 mhz c o - output capacitance (pf) 0.01 0.1 1 10 100 0100200300400 off- s tate leakage current (na) v l -load voltage (v) t = -40 c t = 25 c t = 100 c i f = 0 ma 0 0.1 0.2 0.3 0.4 0.5 0 1020304050 turn-on time (m s ) i f - forward current (ma) t = 25 c t = -40 c t = 100 c i l = 50 ma 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 -40 -20 0 20 40 60 80 100 normalized turn-on time t amb - ambient temperature ( c) normalized to t amb = 25 c i f = 5 ma 0 0.04 0.08 0.12 0.16 0.20 0 1020304050 turn-off time (m s ) i f - forward current (ma) t = 100 c t = 25 c t = -40 c i l = 50 ma
VOR1142M4 www.vishay.com vishay semiconductors rev. 1.1, 17-nov-15 6 document number: 84301 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 14 - normalized turn-off time vs. ambient temperature package dimensions (in millimeters) fig. 15 - package drawing 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 -40 -20 0 20 40 60 80 100 normalized turn-off time t amb - ambient temperature ( c) normalized to t amb = 25 c i f = 5 ma drawing-no.: 6.544-5415.01-4 i ss ue: 2; 23.07.12 recommended footprint 2.54 1.15 5.1 7.4 0.9 12 3 4 pin one i.d. 4.42 0.25 2.12 0.2 0.41 0.1 2.54 nom. 4.92 max. 0.05 0.05 4.57 0.25 5.35 typ. 6.95 0.25 0.2 0.05 0.5 0.15 5 min. lead s coplanarity 0.1 max. technical drawing s according to din s pecification s
VOR1142M4 www.vishay.com vishay semiconductors rev. 1.1, 17-nov-15 7 document number: 84301 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package marking fig. 16 - VOR1142M4 note ? package configuration (t, m) are not part of the package marking. packaging information (in millimeters) fig. 17 - tape and reel pa cking (2000 pieces on reel) solder profiles fig. 18 - lead (pb)-free reflow solder profile according to j-std-020 for smd devices handling and storage conditions esd level: hbm class 2 floor life: unlimited conditions: t amb < 30 c, rh < 85 % moisture sensitivity level 1, according to j-std-020 device per tube type units/tube tubes/box units/box sop-4 100 40 4000 1142 v yww 68 2.0 0.1 4.0 0.1 1.5 0.1 1.75 0.1 1.5 0.1 4.72 0.1 8.0 0.1 7.33 0.1 pin 1 5.5 0.1 12.0 0.3 note: ? cummulative tolerance of 10 s pocket hole s i s 0.20 mm 2.36 0.1 2.66 0.1 0.35 0.05 7.33 0.1 c l 0 50 100 150 200 250 300 0 50 100 150 200 250 300 time (s) temperature (c) 240 c 245 c max. 260 c max. 120 s max. 100 s 217 c max. 30 s max. ramp up 3 c/s max. ramp down 6 c/s 19841 255 c
legal disclaimer notice www.vishay.com vishay revision: 13-jun-16 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners.
|
